Ningguo Kingcool Import and Export Co., Ltd supplies Washing Machine Parts-Tripod Manufacturers components for front-load washer drums, together with a complete range of washing machine, refrigerator, air-conditioner and refrigeration parts. We support appliance factories, service networks and distributors with one-stop sourcing from China.
Tripod and Drum Spider Range for Front-Load Washers
Our tripod range covers the three-arm drum spider that connects the stainless drum to the drum shaft and motor pulley in front-load washing machines. The component carries the drum load, transmits rotation and keeps the drum centred during high-speed spin. We supply tripods as individual service parts and as part of combined washing machine parts orders.
Each tripod is produced to match the drum bore, shaft diameter and mounting hole pattern of the target washer platform. We work from original samples, drawings or model references so the replacement part fits the drum assembly without modification.
Where the Tripod Fits in the Washer Assembly
The tripod sits at the rear of the outer drum, bolted to the inner drum flange and coupled to the drum shaft. It is a structural part: it must resist repeated radial and axial loads, detergent contact and the vibration of unbalanced spin cycles.
- Drum support: three arms distribute load from the drum shell to the shaft.
- Torque transfer: the shaft bore and keyway or spline transmit motor torque to the drum.
- Alignment: machined faces keep the drum concentric with the tub and bearing housing.
- Service access: the tripod is replaced when arms crack, corrode or the shaft seat wears.
Materials and Corrosion Considerations
Tripods are commonly cast or machined from aluminium alloy or die-cast zinc alloy, with some platforms using stainless or coated steel. Aluminium offers a good strength-to-weight ratio for the rotating mass; zinc alloy gives dimensional stability for the shaft seat. The material choice affects weight, corrosion resistance and the torque the spider can carry.
Because the tripod operates in a wet, alkaline environment, surface treatment matters. We confirm the required finish, such as anodising, passivation or protective coating, against the washer platform and the expected service life. For coastal or high-humidity markets, corrosion protection is specified at the quotation stage.
Critical Specifications We Confirm
Before quoting a tripod, we match the mechanical interface to the drum assembly. The table below lists the main variables we use to identify the correct part.
| Specification | What We Match | Why It Matters |
|---|---|---|
| Arm span / bolt circle | Distance across mounting holes | Fits the drum flange without re-drilling |
| Shaft bore and keyway | Diameter, tolerance, key or spline form | Prevents shaft slip and drum wobble |
| Material and finish | Alloy grade, coating or anodising | Corrosion life and load capacity |
| Arm thickness | Section profile and rib design | Stiffness under spin and out-of-balance load |
| Drum capacity | 5 kg to 12 kg and above | Selects the correct load class |
Application Fit Across Washer Platforms
Tripod geometry is platform-specific. We support the common front-load configurations used in household and light commercial washers, including belt-driven and direct-drive drums. The same tripod family can serve different drum sizes where the shaft and bolt pattern are shared.
- Household front-loaders: standard 6–10 kg drums with aluminium or zinc alloy spiders.
- Compact and apartment washers: smaller drum bores with reduced arm span.
- Commercial and laundry equipment: heavier section tripods for higher duty cycles.
- Service and repair: single-unit replacement tripods matched to the washer model.
Quality Control and Acceptance
We inspect tripods at the dimensional and assembly level before packing. Critical checks cover the shaft bore, mounting hole positions, arm flatness and surface finish. Where the customer supplies a drawing, we inspect against the stated tolerances; where the customer supplies a sample, we match the sample interface.
For production orders, we can agree on an inspection plan that includes dimensional reports and visual criteria for casting defects, coating coverage and thread condition. Acceptance is based on the agreed drawing, sample or specification sheet, so both sides work to the same standard.
One-Stop Sourcing with Washing Machine Parts
Tripods are supplied alongside the rest of our washing machine parts range, so a single order can cover the drum assembly and the components around it. This reduces the number of suppliers and consolidates shipping and documentation.
| Part Group | Typical Components | Order Fit |
|---|---|---|
| Drum and drive | Tripod, drum shaft spider, clutch series | Drum rebuild and drive repair |
| Water circuit | Inlet valve, inlet and drain hose, drain motor, pump | Fill and drain service kits |
| Electrical | Capacitor for M/W, universal W/M control system, timer | Control and start-circuit repair |
| Sealing and fittings | Rubber seals, rubber drain valve core, impeller, W/M fittings | Leak prevention and assembly consumables |
Our wider catalogue also covers Air-Conditioner Parts and Refrigerator Parts for appliance distributors that carry multiple product lines.
Information We Use to Configure Your Solution
To quote the correct tripod and avoid fitment returns, we ask for the following project inputs. The more precisely the interface is defined, the faster we can confirm the part.
- Washer brand, model and drum capacity.
- Original part number or a clear photo of the existing tripod.
- Dimensional drawing or sample with shaft bore and bolt circle.
- Material and surface finish requirement.
- Order quantity and expected delivery schedule.
- Packaging and labelling requirements for the destination market.
Packaging, Delivery and Documentation
Tripods are packed to protect the machined shaft seat and mounting faces during transport. We agree the packing format with the customer, from individual cartons to bulk cartons for production lines. Shipping documents, packing lists and inspection records are prepared to match the order scope.
We supply from China to appliance manufacturers, spare-parts distributors and service companies. Orders can combine tripods with other washing machine, refrigeration and air-conditioning parts to make full use of container space.
Frequently Asked Questions
What is a washing machine tripod?
A washing machine tripod, also called a drum shaft spider, is the three-arm bracket that connects the inner drum to the drum shaft. It transfers motor torque to the drum and keeps the drum aligned during spin.
How do I identify the correct tripod for my washer?
Send us the washer brand and model, the original part number if available, and a photo or drawing showing the shaft bore and mounting hole pattern. We match those dimensions to the tripod in our range.
Which materials are used for tripods?
Common materials are aluminium alloy and die-cast zinc alloy, with surface treatments such as anodising or protective coating for corrosion resistance. The material is selected against the drum load and the operating environment.
Can tripods be supplied with other washing machine parts?
Yes. We supply tripods together with inlet valves, drain motors, pumps, capacitors, timers, seals and other washing machine parts, so one order can cover a complete repair or production requirement.
What information is needed for a quotation?
We need the washer model or part number, the interface dimensions, material and finish requirements, order quantity and delivery schedule. With those inputs we confirm the part and prepare the quotation.
Related Products and Categories
Our portfolio also includes Home Appliances Parts for applications with different operating ranges, interfaces or integration requirements.
